It is harmful if ingested or absorbed through the skin and causes sensitization. It can cause severe irritation in contact with eyes and skin. Wash thoroughly after handling. Adequate ventilation is essential. Containers should be tightly closed when not in use or during transportation. Do not inhale mist or vapors. It is recommended to use gloves, safety goggles and protective clothing for safe handling .
Additional information:
The lists that were valid during the creation were used as basis. · Personal protective equipment:
· General protective and hygienic measures: Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing. Wash hands before breaks and at the
end of work. Avoid contact with the eyes and skin. · Breathing equipment: Not required. ·
Protection of hands:
The glove material has to be impermeable and resistant to the product/ the substance/ the
preparation. Due to missing tests no recommendation to the glove material can be given for the
product/ the preparation/ the chemical mixture. Selection of the glove material on consideration
of the penetration times, rates of diffusion and the degradation · Material of gloves The
selection of the suitable gloves does not only depend on the material, but also on further marks
of quality and varies from manufacturer to manufacturer. · Penetration time of glove material
The exact break through time has to be found out by the manufacturer of the protective gloves
and has to be observed. · Eye protection:
9 Physical and chemical properties
General Information Form: Liquid
. Color: Colorless
. Odor: Characteristic
. Change in condition Boiling point/Boiling range: >200°C (>392°F)
· Flash point: >200°C (>392°F)
· Danger of explosion: Product does not present an explosion hazard
· Density at 25°C (77°F): 1.15 - 1.20 g/cm³
. Solubility in / Miscibility with Water: Insoluble
· pH-value: Neutral
Viscosity: Dynamic at 25°C (77°F): 10.000 - 12.000 mPas (Brookfield DV II) .
10 Stability and reactivity
Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications. · Materials to be avoided: Strong Oxidising agents, Strong Alkali, Strong Bases, Amines · Dangerous reactions Reacts with amines with exothermic reaction liberating heat and fumes · Dangerous products of decomposition: Carbon monoxide and carbon dioxide .
11 Toxicological information
Acute toxicity: · Primary irritant effect: · on the skin: Irritant to skin and mucous membranes. · on the eye: Irritating effect. · Sensitization: Sensitization possible through skin contact. .
12 Ecological information
Ecotoxical effects: · Remark: Toxic for fish · General notes: Water hazard class 2 (Assessment by list): hazardous for water Do not allow product to reach ground water, water course or sewage system. Danger to drinking water if even small quantities leak into the ground. Also poisonous for fish and plankton in water bodies. Toxic for aquatic organisms .
13 Disposal considerations
Product: · Recommendation: Must not be disposed of together with household garbage. Do not allow product to reach sewage system. · Uncleaned packaging: · Recommendation: Disposal must be made according to official regulations. .
14 Transport information
· DOT regulations: · Hazard class:
· Land transport ADR/RID (cross-border):
ADR/RID class: 9 Miscellaneous dangerous substances and articles
Danger code (Kemler): 90 ·
UN-Number: 3082
· Packaging group: III
· Label: 9
· Description of goods: 3082 ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
(reaction product: bisphenol-A-(epichlorhydrin) epoxy resin (number average molecular weight ≤
700)
· Maritime transport IMDG:
· IMDG Class: 9 ·
UN Number: 3082
· Label 9 ·
Packaging group: III
· EMS Number: F-A,S-F · Marine
pollutant: YES ·
Propper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
[reaction product bisphenol-A (epichlorohydrin) epoxy resin (number average molecular weight
≤700)]
· Air transport ICAO-TI and IATA-DGR:
· ICAO/IATA Class: 9
· UN/ID Number: 3082
· Label 9
· Special marking: Symbol (fish and tree) ·
Packaging group: III ·
Proper shipping name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
[reaction product bisphenol-A (epichlorohydrin) epoxy resin (number average molecular weight
≤700)]
· UN "Model Regulation": UN3082, ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID,
N.O.S., 9, III
.
15 Regulations
· Sara · Section 355 (extremely hazardous substances): Substance is not listed. · Section 313 (Specific toxic chemical listings): Substance is not listed. · TSCA (Toxic Substances Control Act): Substance is listed. · Proposition 65 · Chemicals known to cause cancer: Substance is not listed. · Chemicals known to cause reproductive toxicity for females: Substance is not listed. · Chemicals known to cause reproductive toxicity for males: Substance is not listed. · Chemicals known to cause developmental toxicity: Substance is not listed. · Carcinogenicity categories · EPA (Environmental Protection Agency) Substance is not listed. · IARC (International Agency for Research on Cancer) Substance is not listed. · NTP (National Toxicology Program) Substance is not listed. · TLV (Threshold Limit Value established by ACGIH) Substance is not listed. · NIOSHCa (National Institute for Occupational Safety and Health) Substance is not listed. · OSHA-Ca (Occupational Safety & Health Administration) Substance is not listed. · Product related hazard informations: The product has been classified and marked in accordance with directives on hazardous materials. · Risk phrases: 36/38 Irritating to eyes and skin. 43 May cause sensitisation by skin contact. 51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment. Safety phrases: 2 Keep out of the reach of children. 28 After contact with skin, wash immediately with plenty of … (to be specified by the manufacturer). 37/39 Wear suitable gloves and eye/face protection. 61 Avoid release to the environment. Refer to special instructions/safety data sheets. · Special labeling of certain preparations: Contains epoxy constituents. See information supplied by the manufacturer. .
16 Other information
This information is based on our present knowledge. However, this shall not constitute a
guarantee for any specific product features and shall not establish a legally valid contractual
relationship.
Abbreviations and acronyms:
ADR: Accord européen sur le transport des marchandises dangereuses par Route (European
Agreement concerning the International Carriage of Dangerous Goods by Road) RID: Règlement
international concernant le transport des marchandises dangereuses par chemin de fer
(Regulations Concerning the International Transport of Dangerous Goods by Rail) IMDG:
International Maritime Code for Dangerous Goods DOT: US Department of Transportation
IATA: International Air Transport Association IATA-DGR: Dangerous Goods Regulations by the
"International Air Transport Association" (IATA) ICAO: International Civil Aviation Organization
ICAO-TI: Technical Instructions by the "International Civil Aviation Organization" (ICAO) GHS:
Globally Harmonized System of Classification and Labelling of Chemicals ACGIH: American
Conference of Governmental Industrial Hygienists EINECS: European Inventory of Existing
Commercial Chemical Substances CAS: Chemical Abstracts Service (division of the American
Chemical Society) NFPA: National Fire Protection Association (USA) HMIS: Hazardous
Materials Identification System (USA)
.
P321 Specific treatment (see on this label).
P332+P313 If skin irritation occurs: Get medical advice/attention.
P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 If eye irritation persists: Get medical advice/attention.
P362 Take off contaminated clothing and wash before reuse. P363 Wash contaminated clothing before reuse.
P391 Collect spillage.
Disposal: P501 Dispose of contents/container in accordance with
local/regional/national/international regulations
4 First aid measures ·
After inhalation: Supply fresh air and to be sure call for a doctor. In case of unconsciousness
place patient stably in side position for transportation. ·
After skin contact: Immediately wash with water and soap and rinse thoroughly.
·
After eye contact: Rinse opened eye for several minutes under running water. If symptoms
persist, consult a doctor.
· After swallowing: If symptoms persist consult doctor.
5 Fire fighting measures
· Suitable extinguishing agents: CO2, extinguishing powder or water spray. Fight larger fires with
water spray or alcohol resistant foam
· For safety reasons unsuitable extinguishing agents: Water spray Extinguishing powder ·
Protective equipment: Wear self-contained respiatory protective device.
6 Accidental release measures
· Person-related safety precautions: Mount respiratory protective device. Remove persons from
danger area. · Measures for environmental protection: Inform respective authorities in case of
seepage into water course or sewage system. Do not allow to enter sewers/ surface or ground
water. · Measures for cleaning/collecting: Large spills: In a clean area, dike and recover for reuse.
Keep out of sewars and waterways. Dispose of contaminated material. Small spills: Use
absorbent pad or mix with absorbent material and dispose
7 Handling and storage · Handling:
· Information for safe handling: Store in cool, dry place in tightly closed receptacles. ·
Information about protection against explosions and fires: Protect from heat. · Storage: ·
Requirements to be met by storerooms and receptacles: Store only in the original receptacle.
Store in a cool location. · Information about storage in one common storage facility: Do not
store together with oxidizing and acidic materials. Store away from oxidizing agents. · Further
information about storage conditions: Keep receptacle tightly sealed.
8 Exposure controls and personal protection
· Additional information about design of technical systems: No further data; see item 7. ·
Components with limit values that require monitoring at the workplace: Not required.
.
Material Safty Data Sheet (MSDS)
BCPCoat Low viscosity Insulation Epoxy Resin-4140 (Part-A)
Description: BCPCoat 4140 is a general purpose low viscosity modified liquid Epoxy Resin,
Applications BCPCoat is suitable for formulating priming coats, solvent-free selfleveling
coatings, Italian Marble , Granites
• Protective Coatings
• Sealing of cracks
2 Composition/Data on components
CAS No. Description
25068-38-6 [Reaction product: bisphenol-A-(epichlorhydrin) epoxy resin (number average
molecular weight ≤ 700)] · Identification number(s)
· NLP Number: 500-033-5 ·
Index number: 603-074-00-8
3 Hazards identification
· Information pertaining to particular dangers for man and environment:
R 36/38 Irritating to eyes and skin.
R 43 May cause sensitisation by skin contact
R 51/53 Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic
environment
Contains epoxy constituents. See information supplied by the manufacturer.
· Classification system: · NFPA ratings (scale 0 - 4)
H315 - Causes skin irritation.
H319 - Causes serious eye irritation.
H317 - May cause an allergic skin reaction
H411 - Toxic to aquatic life with long lasting effects.
Prevention: P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 Wash thoroughly after handling.
P272 Contaminated work clothing should not be allowed out of the workplace.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
Response: P302+P352 IF ON SKIN: Wash with plenty of soap and water.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact
lenses, if present and easy to do. Continue rinsing
.
BATCH NO: 120923
DATE:
BCP Pest Low viscosity Insulation Epoxy Resin M-4140 BATCH NO: 120923
DATE:
BCP Pest Low viscosity Insulation Epoxy Resin M-4140 (Part-A)
Description: BCP pest 4140 is a general purpose low viscosity modified liquid Epoxy Resin,
Applications BCP pest is suitable for formulating priming coats, solvent-free selfleveling
coatings, Italian Marble , Granites
• Protective Coatings
• Sealing of cracks
Product Data Property
Unit
BCP pest 4140
Resut
Appearance
Clear liquid
Colour (Gardner)
≤ 2 5
Epoxy Index
eq/kg
5.20 – 5.50
5.15
Epoxy equivalent
g/eq
182 – 192
185
Viscosity at 25°C
mpa s
500 – 600
cp@ 515
Density at 20°C
g/cm3
~1.08
Flash Poin
°C
~120
GEL TIME
30 To 35 Minite
35 min
TACKY FREE AT 50 º C
90 To 95 Minits
90 Min
RATIO OF MIXING
4:1
Tensile Strength
55.2 N/mm
Comprssion Strength
113 N/mm
Flexural Strength
95.45 N/mm
SHELF LIFE @ 25º C
24 Month
Properties
Liquid epoxy resin with several applications:
• Versatile, low viscosity, good workability with wide range of hardeners
• Excellent mechanical properties and chemical resistance
• Very good processing properties
Mix Ratio
Components
Parts by Weigh
Components
Parts by Weight
BCP Resin 4140
100
BCP pest Hardeer 4140 25
Storage
BCP pest Resin should be stored in a dry place, preferably in the sealed
original
container, at temperatures between 2°C to 40°C. It should not be exposed to
direct sun light. should not be exposed to
direct sun light.
.